Just insert it into the only orientation it works in, push it down tight into the steering wheel and tighten the screws on the sides. The screws should go on very tight to detract from theft or malfunction.
Replace the plastic plates on the side which just pop back into place and you are all finished. Even if you have reinstalled every sensor and airbag, the airbag may still need to be reset which can be done by a dealership. This guide offers no guarantee that the airbag system will work until it has been checked by an authorized facility. How to remove the steering wheel. Click for a Quote or Questions. This article is written for you. Remove the steering wheel as follows: For car without air bags: Remove the steering wheel horn pad by pulling firmly on the pad.
If you have an aftermarket wheel i. Momo with a center horn button, gently pry around the outside of the button with a small flat tip screwdriver or probe to dislodge the button from the wheel. Disconnect the wire from the back of the horn button. Using a paint pen, finger nail polish, or other appropriate marker, mark the orientation of the steering wheel to the splines on the end of the steering column shaft.
Pull the steering wheel straight off the end of the steering column. For cars with air bags: The air bag can be removed after the battery has been disconnected for at least 30 minutes. On the back side of the steering wheel there are two Torx head screws which are recessed into the back of the column.
Using a T30 Torx socket and ratchet, remove the screws. Slide the air bag assembly off of the front of the steering column and disconnect the plug on the back of the air bag. Set the air bag aside where it can not get damaged face up. Installation Slide the steering wheel on to the steering column paying attention to the alignment marks made during removal. Install the wheel retaining nut and torque to 45 Nm 33 ft-lbs. For non-airbag cars attach the horn button wire to the horn button pad and press the pad into place on the steering wheel.
For airbag equipped cars, attach the wire to the back of the airbag, slide it into the steering wheel, and attach by installing the two Torx head screws T Standing outside the car reach into the car and turn the ignition on. Start the car and see if the airbag warning light is illuminated. Mine was on very tight and required some force to loosen.
Remove the screws from both sides. Getting the wiring ribbon cable back in place. Make sure you warm the pulley to about degrees F and then reinstall the pulley. The installation of the pulley should be done in a clean, rust-free shaft. If the shaft and the pulley are not cleaned, then the installation process can become difficult and lengthy. Note: Do not lubricate the pulley or shaft with any grease, water, or any liquid.
If, by any chance, grease or oil is present, make sure to clean it before installation. Lubrication can cause the pulley to slip and result in failure installation.
As we want the pulley to warm at degrees. Once we achieve the exact temperature, it is the perfect time to align the pulley onto the shaft. Now you need to spin the pulley till it ensures a square mount gently.
Forming a square mount will start the alignment to form correctly before any installation. Now it is time to turn the pulley on and take the wobble out.
This indicates that the pulley is square and perfect. Next up, we will connect the installation tool in front of the input shaft pump. With step 6, the installation will be completed. Now you need to tighten the collar against the pulley. Again continue to tighten the installation with a ratchet and wrenches.
Make sure you have not left any loss areas. Continue to tighten the tool until the power steering pulley is thoroughly installed. It needs to be flushed together with the pump input shaft.
Once you ensure that the pulley is completed flushed along with the shaft, here the installation is done. Never try to remove or install a power steering pulley with the help of a hammer. Make sure you undergo each step carefully and keep the necessary precautions in mind.
Also, the pre-removal steps are important as they are some steps that need to be done before operation any car-related actions. I hope this article would have helped you to remove power steering pulley without pulley. See you soon with another amazing article. Your email address will not be published.
0コメント